We have discovered the article on Tools You Need to Install a New Bathtub directly below on the web and reckoned it made sense to relate it with you on this page.
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately hard task. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have actually qualified yourself for the work as well as fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This article will certainly assist you install a brand-new bath tub in your restroom if you have actually currently purchased a new bathtub as well as do not require to change the arrangement of your previous water pipes.
Your tools and also product checklist ought to consist of the following:
- New Tub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Tape Measure
- Pipe Caps
Planning for the Setup
First of all, the supporting structure supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be rather troublesome as a result of the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub up until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and also check all joints and new pipework for leaks and tighten them if required. Fill the bathtub and also check the overflow outlet as well as the normal outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub must wait up until the tub has been utilized a minimum of once as this will settle it into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the tap and also the sink. Protect the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bathroom and the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealant can break relatively very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that article on Installing A Bathtub from someone on another web blog. Are you aware of somebody who is fascinated with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Do not hesitate to promote it. I love reading our article about How to Install a Bathtub Yourself.
Or Book Technician Here
Comments on “Exactly How to Install a Bath Tub in Your Bathroom”